Versalift SST-40-EIH SOLD

Description

We are pleased to quote the VERSALIFT SST-40-EIH-02, insulated 40 ft. articulating, telescopic aerial platform lift, 45 ft. working height including the following items:

• Standard platform capacity of 350 lbs. (158.7 kg).
• VERSALIFT TruGuard™ dielectric isolating system with right hand single stick control. All control handles are isolated and tested per ANSI 92.2. The high resistive dielectric system is protected from direct environmental and job related contamination. TruGuard™ technology incorporates the use of full hydraulic controls with durable metal handles and linkages.
• 180° hydraulic platform rotator.
• Full pressure turret mounted lower controls including override.
• Engine start/stop system with controls at platform and lower controls.
• Continuous unrestricted rotation including three pass collector ring.
• Five GPM (19.0 LPM) open center hydraulic system.
• Chassis insulating system (lower boom insert) including fiberglass compensation link providing 12 inches (0.30 m) insulation gap.
• Fiberglass inner boom and patented ELECTROGARD providing 42 in. (1.07 m) insulation gap fully retracted meeting ANSI A92.2 requirements for Category C, 46 KV and below.
• Hydraulic tool power at bucket. Quick disconnect couplers not included.
• ELECTROGARD and inner boom finished with white urethane paint over white gel coat.
• Integral hydraulic oil reservoir with dual sight gauges and 15 gal. (56.8 l) capacity.
• End mounted closed 24 in. x 30 in. x 42 in. (0.61 m x 0.76 m x 1.07 m) fiberglass platform with one step, liner and cover.
• Master/slave hydraulic leveling with upper control to tilt for clean-out and rescue. Leveling control at lower controls.
• Non‑lube bearings used at all pivot points.
• Multi‑link hose carrier system through booms.
• Boom cradle and ratchet type tie down strap.
• Auto throttle control.
• 12 Volt DC backup pump providing power to all boom functions.
• Mounting hardware for chassis/cab installation.
• Full body harness and lanyard.
• Painted standard white urethane.
• Two operator’s manuals and two service manuals.
• ANSI A92.2 data plate.

Cab and chassis to the following specifications:

• 2022 Ford F-550 4×4 cab and chassis with a CA of 84”
• GVWR: 19,500 lbs payload plus upgrade package.
• XL Value Package includes 4.2” center-stack screen and SYNC communications system
• Power equipment package includes power windows, door locks and remote keyless entry.
• Steering wheel mounted cruise control.
• 7L 4V OHV Power Stroke V8 turbo diesel engine
• TorqShift 10-speed automatic transmission
• Snow plow prep package including dual alternators (Total 332-Amps)
• 88 limited slip axle.
• Air conditioning.
• Engine block heater
• 225/70Rx19.5G BSW traction tires.
• Utility lighting system
• Radio: AM/FM stereo includes 4 speakers.
• HD vinyl 40/20/40 slit bench seat
• Trailer brake controller
• Operator Commanded Regeneration (OCR)
• Rear view camera and prep kit
• Painted Oxford White.

Brand FX Bodies 132” long x 42” high x 94” wide service body including the following:

• 30 inch aluminum tread plate platform extension
• BFX LED lighting package installed in tail shelf.
• Cable access step at rear and side access.
• Two (2) stainless steel grab handles at side access and two (2) aluminum grab rails at rear tail shelf.
• Wheel chock storage and outrigger pad holders.
• Push/pull rod lock system
  • 42” High Street side compartments as follows
• 1^st Vertical: Two (2) adjustable shelves with dividers
• 2^nd Vertical: Two (2) adjustable shelves with dividers
• Horizontal: One (1) removable shelf with dividers
• Rear Vertical: Two (2) adjustable shelves with dividers
• Hot stick shelf with rear access door.
  • 42” High Curbside compartments as follows
• 1^st Vertical: Two (2) adjustable shelves with dividers and cutout for outrigger
• 2^nd Vertical: Grip strut access steps to bed area with removable plastic tail board.
• Horizontal: One (1) adjustable shelf with dividers
• Rear Vertical: Five (5) fixed material hooks 1-3-1

Installation to include the following:

• Install VERSALIFT SST-40-EIH, mounting hardware, PTO and pump.
• Install rear torsion bar and ballast
• Install service body and accessories.
• Install combination pintle hitch with 2” ball, D rings and 7 prong trailer connector
• Install two (2) amber strobe lights in tail shelf and two (2) strobes lights in front grill
• Install mud flaps, back up alarm and park brake interlock system.
• Furnish fire extinguisher, 3 piece triangle reflector kit and wheel chocks.
• Test ride completed unit for 1 hour.
• Test and certify per ANSI A92.2